HOW TO FIX IT WHEN YOU WARPED THE LOOM BACKWARDS!!!

 A common mistake made by new weavers and some distracted experienced weavers is warping their rigid heddle loom backwards. Just what does that mean?  They have warped the loom so that the warp has been placed on the cloth/weaving side of the loom OR THE FRONT SIDE OF THE LOOM WHEN IT BELONGS ON THE BACK SIDE OF THE LOOM. A rigid heddle loom has two distinctly different sides - and they are easy to tell apart. The warp side of the loom - the side you put the warp onto the apron rod and wind onto the beam on is the BACK OF THE LOOM - and you can tell because it is the SHORT side of the loom - from the heddle to the beam.  The cloth/weaving side of the loom is the FRONT OF THE LOOM - and you can tell because it is the LONG side of the loom - from the heddle to the beam.  The side you weave on is longer to give you more room to weave in. The side the warp is put on is shorter because all that side is doing is holding the warp rolled up on the beam. 

So what happens if the loom is warped backwards. You could still weave this way but you will not have very much room to weave in. Will the weave be different? Likely no. BUT you will be advancing the warp much more often and spending time you could have just kept weaving doing so. 

Here is the simple way to fix warping the loom backwards and getting the warp from the wrong beam onto the right beam.  It might seem obvious that you just wind the warp from one beam to the other - which basically is what is done BUT when the warp is wound onto the beam when the loom is warped correctly, tension needs to be placed on the warp as you wind so that the warp will have even tension when you weave AND at the same time as winding on a warp separator of some type - brown package wrapping paper or rubber no slip grip shelf liner or warp sticks - need to be placed between the rows of warp to keep the warp from falling into the row below which will mess up the warp tension.  Follow the these instructions and you will get the warp onto the correct beam easily and fairly quickly. Just to note - this process is easier to do with a helper, but it can be done alone. I will point out where a helper comes in handy. 

1) If you have not already done so, warp the holes.

2) Take the warp that is on the back side of the loom now (the warp is wound on the front beam) and tie it onto the apron rod attached to the back beam.  Do this just the same way you would do it on the front of the loom had you warped correctly. You can use knots or lash on - which ever is your preference. Once the warp is tied on, adjust the tension on the warp just as you would do when the loom is warped correctly.

3) You now have a loom with warp attached to both beams - they are just not the right beams. Now, you will begin to start fixing it. Have your warp separator handy. If you are going to have a helper - have the helper ready to help. 

4) Set the pawl (latch) on the BACK beam - the beam with  no warp wound on - OFF the ratchet. (Ratchet looks like a gear. Pawl is a latch that locks into the teeth of the gear.) 

5) Put one hand on the front beam - where the warp is wound onto and hold the beam from turning. IF USING A HELPER - THIS IS THE HELPER'S JOB - SO GET THE HELPER TO HOLD THE FRONT BEAM. 

6) If it is just you alone, with your other hand release the the pawl from the ratchet on the FRONT beam AND DO NOT LET GO OF THE FRONT BEAM. If you have a helper and are not holding the beam with your hand - then do the same WHILE THE HELPER DOES NOT LET GO OF THE FRONT BEAM.  

7) IF USING A HELPER - THE HELPER HOLDS THE FRONT BEAM AND NEVER LETS GO BUT ALLOWS THE BEAM TO TURN WITH RESISTANCE, PUTTING TENSION ON THE WARP AS IT WINDS ONTO THE BACK BEAM WHERE IT BELONGS. IF YOU ARE ALONE - with one hand you are going to hold the front beam and put RESISTANCE on it to put tension on the warp, as you wind on with the other hand.

8) When you need to add another sheet of warp separator or another warp stick, lock both beams with the ratchet and pawl - to free both of your hands - and add the sheet or put in the warp stick. 

9) Unlock the FRONT BEAM AGAIN - and still either you or the helper HOLDING THE FRONT BEAM TO PUT TENSION ON THE WARP - start winding on again. 

10) Repeat 8 and 9 until you have finished winding the warp onto the BACK BEAM. 

11) Your loom is NOW warped correctly! The only difference from having done this right from the start is that the warp is going around the apron rod on the front of the loom and is tied onto the apron rod on the back of the loom. THIS WILL NOT EFFECT THE WEAVE. You may still need to weave a header - it is actually a good idea to do that even if the warp looks evenly spaced on the front of the loom. 

12) YOU ARE READY TO WEAVE!

That is it - 12 simple steps.  Having a helper is less awkward in what the weaver has to do to get the loom wound on, but if you can reach hold the opposite beam while you wind on from the other side of the loom, it can be done! 😃  

THINGS TO KNOW WHEN DIRECT WARPING

 There are some things that should be more clearly stated about direct warping that go beyond the back process and often are left out all together.  One of the first things to understand is that when direct warping - whether you are using a single vertical peg, or a horizontal rod as I have described in the article on this site, "Another Way to Direct Warp", multiple pegs, or hybrid warping using a warping board to direct warp - is that all you are doing when you bring the yarn from the loom to the warping peg (etc.) is measuring the yarn to weave the length you want your weave to be on the loom.  That length of warp on the loom is not the length of warp you want your final off the loom length to be. It is longer to account for shrinkage, waste, fringe, tie on, etc. This length is calculated as part of your project calculations with a weaving calculator.  To get that length that the calculator gives you for your warp you need to measure the distance from the warping peg to the position of the apron rod in the back of your loom at which you will warp to.  With a single peg - measure from the center of your loom - to the peg. 

When you warp to a single peg your warp is creating a V shape with the point of the V at the peg and the top of the V at each end of the warp on your heddle. Geometry tells us that the distance from the point of the V to the center point between the two legs of the V at the top of the V is shorter than the the length of each arm of the V. (This can be confusing at first - so take a moment to read that last sentence again and let it sink in.) What does this mean? It means that the warp at the center of the loom is shorter than the warp at the ends - and this distance right and left of the center of your heddle gets longer. You want all of the warp yarn to be AT LEAST the length of the  center of the heddle to the peg. This means you will have longer warp on the sides - but that is necessary when warping with a single peg - or your warp will be too short for your project.  Are you wasting some yarn? Yes. Is there a way around that? Not if you warp to a single peg. With a horizontal rod to warp to you should have equal lengths of warp from heddle to rod. With a warping board for hybrid warp, you will still have the V. With multiple pegs, you will have less of a V though you will create multiple Vs warping to multiple pegs and yarn length will still vary but not as much.. 

 When new weavers direct warp - and some experienced weavers as well who have not figured out this next thing - they often find the warp peg come flying off the table it is attached to and the peg and the yarn come at them at the loom resulting in warp tangled on the floor. Sometimes the warp can be salvaged and sometimes it can't. This happens to many - it happened to me on my second project ever and it happened twice during that warp. The first time I could salvage the yarn. The second time I could not.  Why does this happen? There is too much tension on the warp between the loom and the peg. 

There is no need to have tension on the warp when you are warping to the peg! As we just established above you are measuring the yarn when you warp to the peg. If there is tension on the warp, the warp acts like a spring - if you pull a spring too much it wants to spring back! The peg will only take so much before the warp wants to pull it in the direction from which it is being pulled - and it is going to go flying.  To prevent this there are two things you can do - one is to clamp the peg on the far side of the table and never the side closest to the loom. Closest to the loom if the peg is pulled it has nowhere to go but at you. On the other side of the table when it is pulled it will first pull itself into the edge of the table it is clamped to. But sometimes even that will not stop it and it still comes flying off with the warp. Or the pulling causes the warp to travel up the peg and come off the top.

One other thing that happens when there is too much tension on the warp from the loom to the peg is that you are stretching the yarn. Again, think of the yarn as a spring. As it is pulled it gets longer - much longer than the spring is when it is not being stretched from pulling. And since you are measuring the yarn to the peg, what is happening with the yarn under tension is that when you take the warp off the peg to wind it on the back beam as soon as it is off the top of the peg, the warp yarn RELAXES! And it gets SHORTER! Oops! What you thought was 90" long was stretched to 90" long and it really is 85 inches long or shorter! Your warp is too short for the length of the project you intended to weave, and you won't know it until you get near the end of your warp on the loom while weaving and you are no where near the length you thought you would have.

There is no reason for the tension. It is OK for your warp to sag from the loom to the peg AS LONG AS it sags consistently from one end of the heddle to the other.  This is not a problem. It may be a little longer than you need BUT LONGER IS BETTER THAN SHORTER when it comes to warp! 

But the books say to wind the warp onto the back beam under tension! Yes, it does but you have not been winding on yet - you are just measuring your yarn from the loom to the peg while you warp. When you have warped all of the slots and take the warp off the peg to wind it onto the back beam THAT IS WHEN YOU PUT THE WARP UNDER TENSION. 

When you are more experienced these things start to click and make sense. It really is simple but you don't usually see this in a book or even in the videos showing direct warp to a rigid heddle loom. 

What else can go wrong?  Lets go back a little - before you have warped the loom but are about to start. Look at your loom. The heddle is generally located not at the center of the loom but more toward the back of the loom frame. The space from the heddle to the back of the loom is shorter than the heddle to the front of the loom. SHORT END IS THE BACK OF THE LOOM. LONG END IS THE FRONT OF THE LOOM. THE BACK OF THE LOOM IS THE WARP END. THE FRONT OF THE LOOM IS THE WEAVING AND FINISHED CLOTH END. Before you warp make sure your loom is facing the correct way. AND when direct warping you put the FRONT of the loom toward the warp peg. You bring the warp from the ball of yarn around the back APRON ROD (the apron rod is the dowel or flat "stick" that you attach the warp to) through the slot in the heddle and over to the direct peg - put ir over the peg and come back to do this again for the width of your warp in the heddle.  So now you know what is the back of the loom and what is the front of the loom. You do not want to weave from the back of the loom - the space between the heddle and the beam is just too short.  Weaving is done on the front of the loom - the long part of the loom.  

ALWAYS WARP SO THAT THE YARN IS CENTERED ON THE HEDDLE. (When you get a new heddle the first thing you should do is take a marking pen and make a mark on the heddle frame at the center of the heddle - either that will correspond to a slot or a hole.)  Do not warp with the yarn on one side of the heddle and the rest of the heddle is empty. As you weave you are weaving with the warp under strong tension between the beams. If you are not centered you are pulling he beams on the side the warp is on and the empty side is going to try to flex - which can break the beam. When planning out where your warp will go on the heddle - with the heddle off the loom and in front of you on a table, start at the middle slot and count out to the right and then to the left to find the starting warp slot and the ending warp slot with the center slot in the middle. This means when you count to one side, count the center slot BUT when you count then to the other side do not count the center slot it is already counted - start in that direction with the slot next to the center slot. A simple tip is to take a piece of yarn and tie it around the top of the frame of the loom through the starting slot and another through the ending slot. On the loom when warping start at one marked slot and stop at the other marked slot. If you often use the same widths to weave on that heddle - keep the marking yarns tied on  - use a different color pair of yarns for different weaving widths and make a note of which is which width. (Sounds like it is part of a song in the Wizard of Oz! 😀 )  And before I start singing - we will move on. 😉

Also before you start weaving, you may notice that the heddle (on some looms) is different on one side from the other side. On some rigid heddle looms the heddle is bumped out on one side. On other rigid heddle looms the heddle is flat on both sides. So which is the front of the heddle and which is the back?  With a heddle that is flat on both sides it does not matter. But guess what? On a heddle with the bump out on one side and flat on the other it also does not matter.  Kromski looms and Ashford looms have heddles made with the bump out on one side of the plastic of the heddle - it is in the area of the hole. One thing that this does is strengthen the plastic around the hole. Yarn passing through the hole constantly is not going to wear through that thicker plastic that forms the bump. But is there a front and back and a right side and a wrong side to use to beat with? Not really. Some will say the name of the company that made the heddle is on the front of the heddle. Hmm? Kromski puts the name on the heddle on the same side as the bump out. Ashford puts the name of the heddle on the flat side of the heddle. Which one is right? It is really a matter of personal preference. My own preference is to beat with the heddle with the bump out. I find that it pushes the weft row more directly than the flat side BUT am I right? Some like using the flat side.  Are they wrong? Some looms only have a heddle that is flat on both sides. Is that a problem? NO! There are as many using the bumped out side to beat with as there are those using the flat side when their heddles have two different sides. (An interesting side note - Kromski's 10 dent heddle is flat on both sides. When I asked them about this they had no answer as to why the 10 dent is flat and the 5, 8, and 12 dent heddles are bumped out on one side.) So decide for yourself if you have a bumped out heddle on one side. Try a project one way and another project the other way - and see which you prefer or conclude that there is no preference. 

OK - here is something that comes up in discussions often. You will see in books and in videos on direct warping that it is said that when you put the yarn around the apron rod to put it in the slot you MUST alternate the yarn going over and under the apron rod - first over, then under. When I first started weaving I was making myself crazy making sure that I got this right - checking with each warp slot that I passed the loop of yarn through. GUESS WHAT? The yarn goes this way whether you think about it or not. It can only go this way - over and under alternating - it does it itself. If it is not, you did something wrong in bringing the yarn from the ball to go around the apron rod and through the slot. It really cannot go any other way if you are warping correctly. 

 When you wind the warp onto the back beam, you are winding the apron rod on with the warp tied on  to it and with the warp UNDER TENSION (how you put the tension on is another article in itself), you must put a warp separator under every layer of warp that you wind on. Warp separator can be as simple as sheets of brown package wrapping paper. A warp separator must be thick and it must not compress so that the one layer of warp sinks into the war layer below. Thin paper - even thin cloth  is not a good warp separator as it will push in with each warp under tension and push into the row below and maybe even rip the paper. The purpose of the separator is to keep each layer of warp apart and not mixing into the layer below.  Some use flat strips of wood put in between the warp as it is wound on. Some use the rubber no slip shelf liner - the one with the bumps on the surface of rubber. Many use the package wrapping paper which is sold in office stores or even Walmart in the stationary aisle. That paper lasts for a long time and many weaves.

There is such a thing as double warp. I am not going to go into how that is done but know that it is two warp threads in each slot and each hole. The yarn that this is done with MUST be thin enough to fit doubled in a slot and in a hole. Don't force it in - it will just rub and break as you are weaving. A beginning weaver should not be doing double warp until they have a lot of experience with single regular warp.

What can go wrong while warping? 

 If you find that there is not enough warp yarn on the ball after you have been warping and then passing  the loop through the slot in the heddle does not make it to the peg, stop and bring that loop back to the loom. Pass it back through to the back of the heddle and tie it onto the apron rod. Get another ball of warp yarn and tie the end on the apron rod and keep warping, Make sure you are starting in the now empty slot that you found the warp was too short to make it to the peg. It is always good to have another ball of yarn on hand - for warp and for weft.

Before you take your warp off the warping peg, go across every slot and make sure you have not missed any slots that needed a warp loop going to the peg. It is far easier now to fix this than later.

When tying on the warp to the warp apron rod - at the start of your warp or at the end - or in between - make sure your knots are strong and cannot come loose. A loose knot here will cause problems when you get toward the end of the weave. Double - even triple knots are good! 

When you have tied your warp to the front beam, every bundle of warp that is tied on must be equal in tension to all of the others. Go along the bundles and the warp behind the heddle with two fingers and tap gently. Every bundle must feel the same tension. If not you will have problems when you weave. It can take multiple adjustments back and forth across the warp bundles to get them even. Time spent here with this will save problems later.

 

Once you have finished warping go and read my article on weaving a header. That is the next thing you have to do before you start weaving with your project yarn! 

 

Yes, the Kromski Heddle Does Stay in the Up Position on the Loom

I often see comments about how someone's Kromski heddle on their Kromski loom will not stay in the up position on their loom. I have answered this many times and it is time I wrote an article about it.

The Kromski heddle and heddle blocks are designed to hold the loom solid in the up position IF the tension on the warp is fairly tight. Not break the beam tight but it is best described as drum tight. That is a term I have used when teaching miniature punchneedle embroidery which also needs to have the cloth in the hoop "drum tight". On the hoop it is easy to explain - tap on the top of the cloth in the hoop and it sounds like a little drum. With the loom, the warp is not going to make any sound if you tap on it, but if you push gently down on it about an inch down there should be resistance. Here is a photo with my fingers pushing down on the warp when the heddle is in the up position -

You see just three fingers lightly pushing down. On just the warp threads it pushes only slightly further (a photo did not show this well). Getting the tension here is not hard. Wind the warp to put some tension on it. Put the heddle heddle up. If it does not stay up by itself or it falls, increase the tension on the warp to the point that the heddle is solid on the top of the blocks. Like this -

See how the warp holds the heddle in place. And see that there are on need for rubber bands wrapped around the top of the heddle block and there is certainly no need for cutting into the notch on the top of the heddle block! Wow! Somethings that I have heard people do rather than get the heddle to stand as it was intended to.

Once it is staying up there, if you feel there is too much tension, then open a pawl (front or back) and move the ratchet one or two notches less. Put the pawl back on the ratchet to lock it and put the heddle back up - if it stays fine. If not, the tension has to go back to where it was - one notch at a time if you lowered it more than one notch.

One thing to know about putting the heddle in both the top and bottom positions is that you pivot the heddle into place. See how the bottom of the heddle frame sits in the notch in the photo above. Put it there first on an angle with the top of the heddle toward you and push the top of the frame up to put the loom straight on the block. It will move against the back of the notch and stay there.

For putting the heddle in the bottom position it is the same thing - with this same tension, put the TOP corner of the heddle frame on the top notch - both sides at the same time - always - and have the bottom of the heddle frame coming toward you. Have your thumbs push the top of the frame toward the back of the loom so that the bottom of the heddle swings into place to the bottom of the heddle block - and it will make a sound "SNAP" - you might even say "Pop" as in Pop Goes the Heddle. 😄 It makes a very definite connection - and stays there!  I love the sound the heddle makes when it snaps into place on the bottom position.

Here is the heddle in the bottom position -

So - it really does work. Don't crank up your tension to the point that it will do damage - but the tension has to be correct for the Kromski heddle to stay solidly in place - up or down! And each time you advance the warp you are releasing the tension to wind the cloth on the front beam and when done you need to return the tension to where it was.

When you finish weaving for the day - or will be away from the loom for several hours, take the tension off the warp - just enough for the warp and cloth to go slightly slack - not too much! This will reduce any stretch on the warp and also any stress on the loom while you are not weaving. 

A Simple Tip When Warping a Rigid Heddle Loom

My Kromski loom came with something that Kromski calls a "Warp Helper". It is a block of wood with a rectangular slot in the bottom and a hole through the top - for the apron dowel to slide through to hold the dowel while you warp. On my 32" loom the dowel both pulls this block off the edge of the loom that you are supposed to push it down on and the length of the dowel cannot be supported by a single block like this. I tried to make my own similar blocks and none really were very satisfactory. The idea is that the warp dowel needs to be held while the warp is being tied on to it. I have since watched Kromski's video on using this and saw that if one were warping on a warping board and then transfering the yarn to the loom to tie onto the warp beam, the Kromski warp helper will work, but when direct warping - which is so common with a rigid heddle loom - the block does not work well.

So what to do to hold the warp dowel when warping - and then again hold the cloth side dowel when tying on the warp on that side? The answer just came to me one day and it is SO simple that it is just silly that this is not shown all of the time!

I used rubber bands. Not special rubber bands but thick and strong rubber bands. These are the type of rubber bands that the post office uses. And they can be found where stationary is sold - Walmart, Staples, or other office stores or stationary sections in a bag of many for just a few dollars. You will get more rubber bands in that bag than you will ever need. Here in photos I can show you much easier what I am talking about.

You have your apron rod or dowel that you are going to tie your first warp thread on, and take a loop from that thread through your heddle slot to your warping peg and back again - but the dowel is just hanging there. Wouldn't it be easier if it was up and supported in front of you - straight across the back of the loom?  Take a look here -

Here you can see the apron rod for the warp - in the back of the loom. You are looking from the front to the back. See how the rod (what the warp loops around) is sticking straight across - with its cords stretched out behind it connected to the warp beam. Now look to the left of the photo from the end of the heddle back. Wait - here is a close up of that -

See the rubber band? So simple. There is a rubber band on each side of the loom. One end of one rubber band goes around the top of the heddle block and the other end goes around the end of the apron rod (or dowel). Do this on each side. Put the rubber band on, and crank back your apron rod to put some tension on the rubber band. Position the rod where it is comfortable for you to tie and wrap onto it as you warp. Can you believe how simple this is.

Now, once you have all of your warp on the warp apron rod, take the rubber bands off BEFORE you start winding your warp on the warp beam. This is easy to forget - but you will not be happy if you leave those two rubber bands in place. BUT just put them aside, you still need them!


The warp is all set on the warp beam. You have taken one warp out of each slot and put it in the adjacent hole. You are now ready to tie it on the front beam. And you are going to use your rubber bands again. You will do the exact same thing but now on the front dowel.

Take a look -  

It is hard to see but there is a rubber band on both the left and the right sides. Here is a close up of the right side.

With the dowel straight across and being held in place with the rubber bands, start tying your warp on the front beam. Here are close ups of the rubber bands going around the top of the heddle block and dowel end.

Once you start tying your warp bundles on to the dowel and you have enough evenly on both sides of the dowel to support the rod with the warp, you can take the rubber bands off. I have left them on until the end, but I have been finding that they might interfere with getting a good tension before you make your final adjustments of each bundle to get even tension on each. No matter what - you must take these rubber bands OFF BEFORE you start to make your adjustments of tension on each bundle. If you don't you will not have correct tension on your warp to weave with.

You can certainly use each rubber band many times but if you use two that have stretched out unevenly, you will put your dowel at an angle. Just take a look at how far each end of the dowel is from the heddle - the two measurements should be equal. A simple ruler put from the heddle to the dowel on each end will tell you immediately if you need to put these rubber bands aside and take two new ones. Those rubber bands are still good - for the usual uses for rubber bands.

This will work on any Rigid Heddle Loom - as long as there is part of the heddle block sticking up to put the rubber band around.

So you see, two simple rubber bands can make a job that potentially can be frustrating simple and easy!

Another way to Direct Warp

Direct warping is a method of measuring the yarn for your warp at the same time that you are putting it on the loom. The usual method of direct warping - and there are many free videos on YouTube to show how to do this - is to clamp an vertical peg to a table (some use the top of a chair back) that is the distance from the apron dowel of your loom that the warp is to be long, and warp from the back of the loom tying your first warp thread to the apron dowel and then passing a loop of that warp through the first slot you have calculated to start your warp in to go across the loom the number of slots and holes also calculated. The heddle hook or slay hook is used to pick up the loop from the opposite side of the heddle, through the slot toward you and then catching the loop and pulling from back to front through that slot. This puts TWO warp threads (it is a loop that is going through) now on the cloth side of the heddle. You get up, take that loop in your fingers and walk it across the room to the warping peg and place the loop over and down on the vertical peg. You carry the yarn now back with you to the loom and then continue with the warp thread (placed under the loom on the warp side) and keep passing loops through. This is a simplified explanation of the process.

Now, what can go wrong? Well, if you put too much tension on that warp loop as you carry it down to the peg, you transfer that tension to the warp on the peg when you put it on - and you may just find that the peg comes flying off the table - and all the warp becomes a tangled mess on the floor - sometimes impossible to get straightened out - and usually just as you were about to finish the warp. That is one thing that can go wrong. Another problem is that if the peg is not tall enough, you can run out of peg before you are finished and you will find yourself pushing it all down as best you can to make more room. And still another problem is that with the warp going across the loom to a single point - the peg - you create a V from peg to loom with the closed end of the V at the peg. The distance from each side of the loom to the middle will be at different lengths.

So what can you do about this. I was a wonderful idea shared on one of the Weaving Facebook groups by a very smart lady, Ingrid Koch. She came up with a horizontal warping rod instead of a warping peg. As I recall, she used a curtain rod. I looked at her idea and decided to come up with something a little stronger and a way to secure it to a table.

I decided to use a thick wood dowel - about 3/4" in diameter and three feet wide. My loom is 32" wide so the 36" long dowel was more than enough for a full warp across the loom. Here is a photo of what I came up with -

What you see here are two stand brackets to hold the rod. The table they are on is a garden folding table from IKEA and I bought this table for this purpose - and to use for other weaving related tasks. With this table the brackets are held down to the surface of the table with a screw bolt passed up through the slot of the table through the bracket and tightened on with a wing nut - there is a washer both above and below the bracket. One bracket is cut shorter than the other, but the bottom of the slot that holds the dowel start at the same height from the table.

 
The rod is level across sitting in the brackets. One side is short because this is the side of the rod that will be lifted to slide the warp loop onto. The other bracket is taller so that the dowel does not slip off as the other end is lifted up.  In this photo you will see a permanent mark in the exact middle of the dowel. You know when you are half way across your heddle your warp should be right there at that mark on the dowel. There are two pieces of removable painters tape that mark the point the first loop should be placed next to - since I warp right to left - that would be the edge of the tape on the right and the spot the last loop is placed - that is the tape on the left. What you see on the right end (outside the bracket on the dowel) is a bubble level. I will explain why that is there later.

So now instead of walking to a vertical peg, with this you walk to the left end of the dowel, lift that end enough to get the warp loop over, and drop the warp loop down at the dowel starting at the edge of the right piece of tape. Let's say I am warping a warp that is to be 104" each warp thread. That warp loop is now 104 inches away from the apron dowel going through the first slot I am warping. The next loop goes right next to that - again 104" long. This goes on for the full width of the warp. When you are done you will have a very straight warp from the warping dowel through the slots in the heddle to and across the apron dowel. This will be the same when the warp is wound onto the warp beam under tension. Every warp thread the same length. All nice and neatly lined up across the beam. If the warp is 12 inches across the apron dowel, it will be 12 inches across the warping rod.

With this, it is hard for the warp to fly off. The brackets are securely attached - you could put these on any table edge using two soft faced wood clamps found at any home or tool store. You have a length of dowel to hold your warp as long as the number of slots you are warping through. You don't have to put a lot of tension on the warp - just enough to keep it from sagging.

Let me step aside a moment to say this - when you are direct warping, your main goal is to measure the warp length and not to put tension on the warp. The tension will be put on by your helper when you wind on the warp on the warp beam.

When you or your partner are taking the rod off the brackets when you are ready to wind the warp onto the back beam, lift it straight up off the brackets just high enough to clear them. You now need to get this to the front of the table. This is easy with this particular table that I picked as it is a gate leg table and what my wife does (who is my warping helper) is move the gate leg closed with her foot from the back of the table and the top comes down. With a table that you cannot do this with, move the rod forward to the front of the table(the tension will be lost but don't worry as the length will not change). Get around to the front and have your helper get hold of the rod  and you move the table so that there is room to get tension back on the warp on the rod. If you remove the warp from the rod at the table, you can warp as you usually would do by tying a string or yarn around all of the warp, and then weight that and warp alone. If you have a helper and you leave the warp on the rod held level and straight as you wind on you will get a nice even warp each thread lying next to each other on your back beam. An alternative is to weight down the table. Leave the warp on the rod and the rod in the brackets, start winding on and let the loom be pulled toward the table and the rod as you wind. Get up and walk behind the loom as you do this.

I mention here about hold the rod level. I find that this makes a difference in getting a good wind when using a rod like this. That mystery item on the right end of the rod in the first photo is a little bubble level. You can find these for a few dollars in Walmart in the Auto section where they have a section of RV supplies. It is a package of two and these little levels have peel and stick adhesive on the bottom. Stick it on the end of the rod and then whoever is holding the rod while you are winding on will see the bubble and if it is not in the middle the rod (dowel) is not level. Move that end up or down a little and the bubble goes to the middle. I added this when my wife said that it looked level as she was holding the dowel in her two hands but was not sure. I could see from across the room that it was way off. She can now see the level and adjust the dowel as needed.

If you leave the warp on the dowel until it gets to the front of the loom, you will have a nice even wind on the beam - every warp thread lined up on the beam just as it will come off the beam while weaving. Thread your holes following the order and you will have no crossed warp threads coming off the warp beam!

This works. I was not happy with the direct warp vertical peg. This solved all of the problems I was having with it!

ADDENDUM:

I have been asked about the size of the table. Here are the dimensions of the table - 28.5" high, 24.5" wide, with one gate leg up - 29.75" long, and with the two gate legs up - 51.75" long.  The table is heavy and I purposely looked for a heavy table so that the table would not move when warping.  The slats in the top make it easy to anchor the brackets. This table from IKEA is an outdoor table - available during the Spring and summer months.This link will bring you to the IKEA page for this table (as long as IKEA still offers this table) -   https://www.ikea.com/us/en/p/aepplaroe-gateleg-table-outdoor-brown-stained-brown-50208535/